Extron TLP Pro 720C Touchpanel Driver
The Extron TLP Pro C is a 7” Cable Cubby® touchpanel with a flip-up, LCD touchscreen. As with all TouchLink® Pro models, this new customizable. 7 Introduction About the TLP Pro C This guide describes the function, installation, and operation of the Extron TLP Pro C TouchLink Pro Touchpanel. The Extron TLP Pro M is a 7” wall mount touchpanel with a high resolution, LCD touchscreen. As with all TouchLink® Pro models, this new customizable.
|Supported systems:||Windows XP, Windows Vista, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10, Windows 10 64 bit|
|Price:||Free* [*Free Registration Required]|
Extron TLP Pro 720C Touchpanel Driver
It is ideal for any AV application requiring a full-size, Cable Cubby touchpanel with a customizable interface.
TouchLink Pro touchpanels operate using standard network infrastructure and are easy to install with reliable and cost effective Ethernet cable. This powerful interface design software offers ready-to-use templates for a wide variety of rooms and presentation environments. Global Configurator Professional or Global Configurator Plus for setting up and configuring the control processor and touchpanel.
See Configuration Extron TLP Pro 720C Touchpanel on page Obtain the following network information from your network administrator: DHCP status on or off. Passwords by default these are either extron for admin or the field is left blank for user. Prepare to Extron TLP Pro 720C Touchpanel the Cable Cubby: Make sure you are familiar with all the included parts see page 6 and have all the necessary tools see page 6 for installing the cable cubby.
Plan where you are going to install the Cable Cubby and how you are going to cut the hole.
KTP - 7” Cable Cubby TouchLink Pro Touchpanel Giao diện cảm ứng
Ensure the TLP Pro C is oriented correctly and that there is adequate room for cables and cable retractors optional. Ensure you are using the correct cut-out template or dimensions see Cut-out Dimensions on page 7.
Ensure the installation complies with all necessary regulations. Mount the Cable Cubby: Cut the table surface see Cutting the Table on page 7. Run all cables to the unit see Running Cables on page 9.
- 19 Best AV images Control system, Wall mount, Audio
- User Guide. TLP Pro C. TouchLink. TouchLink Pro Touchpanel Control Systems Rev. A PDF
- RM 5 - TouchLink Pro Touchpanels Extron
- User Guide. TLP Pro 720C. TouchLink. TouchLink Pro Touchpanel Control Systems Rev. A 09 14
- Shop with confidence
- Extron TLP Pro 720C
Install cable retractors optional see Installing Cable Retractors on page 9. Install the power module optional see Installing Power Modules on page Connect cables to the touchpanel.
Extron TLP Pro C OPS Technology Limited
If required, connect the power supply see Power Connector on page Connect the network cable see Network and Power over Ethernet Connector on page Do not power on the touchpanels or control processors until you have read the Attention notice on Extron TLP Pro 720C Touchpanel 17 12 VDC power supply or on page 19 PoE injector.
Set up the Touchpanels for Network Communication: Connect the PC that you will use for setup, the control processor, and the touchpanel to the same Ethernet subnetwork. Ensure that the edge that opens on the lid is oriented correctly.
Ensure there is enough space for all the system Extron TLP Pro 720C Touchpanel and components, above and below the table. Clearances for under-table cabling, especially if the cable has a large bend radius. Adequate space below the table for cable retractors if they are to be installed see page 7.
The number and type of AAPs required for the installation. The location of devices that connect to the AAPs either above or below the table.
Verify that you have the correct template or dimensions see page 7. Decide on the method for cutting a hole in the table see Cutting the Surface on page 8. There are three methods available: